Peugeot 406

since 1996 release

Repair and operation of the car



Peugeot 406
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engine
+ 4. Cooling systems, heating and ventilation
+ 5. Fuel system
+ 6. System of ignition
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
- 11. Suspension bracket and steering
   11.1. Technical data
   11.2. Rotary fists
   11.3. Replacement of forward hug bearings
   11.4. The lobby is resistant
   11.5. Repair of a forward rack
   11.6. Lower lever of a forward suspension bracket
   11.7. Lower spherical hinge of a forward suspension bracket
   11.8. Stabilizer of cross stability of a forward suspension bracket
   11.9. Coulisse of the stabilizer of cross stability of a forward suspension bracket
   11:10. Lower frame of a forward suspension bracket
   11:11. Nave of a back wheel
   11:12. Replacement of bearings of a back nave
   11:13. Shock-absorber of a back suspension bracket
   11:14. Cylindrical spring of a back suspension bracket
   11:15. Pin of a nave of a back suspension bracket
   11:16. Lower lever of a back suspension bracket
   11:17. Top lever of a back suspension bracket
   11:18. The directing lever of a back suspension bracket
   11:19. Draft of a back suspension bracket
   11:20. Stabilizer of cross stability of a back suspension bracket
   11:21. Coulisse of the stabilizer of cross stability of a back suspension bracket
   11:22. Steering wheel
   11:23. Steering column
   11:24. Intermediate shaft of a steering column
   11:25. Ignition lock
   11:26. Steering mechanism
   11:27. Replacement of protective covers of the steering mechanism
   11:28. Removal of air from system of steering with the amplifier
   11:29. Pump of the amplifier of steering
   11:30. Spherical hinge of steering draft
   11:31. Steering draft
   11:32. Angles of installation of wheels
+ 12. Body
+ 13. Electric equipment
+ 14. Main malfunctions





11:15. Pin of a nave of a back suspension bracket

Removal

PERFORMANCE ORDER
1. Lift a back part of the car and record on supports. Remove the corresponding back wheel.
2. On cars with ABS unscrew a bolt of fastening of the sensor installed on a wheel and take it from a pin.
3. Remove a back nave of a wheel.
4. Using a G-shaped clip, press a brake hose in the place, the closest to the working brake cylinder.
5. Clear dirt traces around connection of a brake tube to the working brake cylinder. Unscrew a connecting nut and take a brake tube from the brake cylinder.
6. Disconnect a cable of the drive of the emergency brake. Unscrew 4 bolts of fastening of a brake board assembled to a pin and remove a board from the car.
7. Establish a jack under the external end of the lower lever and lift a jack so that the back spring slightly contracted.
8. Unscrew a nut and exempt the coulisse of the stabilizer of cross stability from a pin.
9. Unscrew a nut and remove the spherical hinge of the directing lever from a rotary pin.
10. Unscrew bolts and nuts of fastening of external hinges of the lower and top lever.
11. Unscrew a nut and take a bolt of fastening of thirst for a pin. Remove a pin from the car.
12. Check a condition of a pin and, with defects, replace it.

Installation

PERFORMANCE ORDER
1. At installation of a pin it is necessary to use only new nuts. Grease hinged bolts and the surfaces of contact of a suspension bracket with nuts with universal Molykote Q Rapide Plus lubricant.
2. Establish a pin into place, insert external hinged bolts of fastening of a pin to the top and lower lever and a draft bolt. Screw a hand on bolts new nuts.
3. Establish the coulisse of the stabilizer of cross stability and the spherical hinge of the directing lever. Fix by new nuts, tightening them the required moment.
4. Establish a brake board assembled on a pin and tighten bolts of fastening of a board the required moment.
5. Establish a nave on a pin.
6. Connect a brake pipe to the working brake cylinder and tighten a fastening nut the required moment. Remove a clip from a brake hose and remove air from the brake system.
7. On models with ABS install the sensor of rotation of a wheel on a rotary pin.
8. Establish a back wheel and lower the car. Shake the car that all elements of a suspension bracket rose on the places. Tighten nuts of fastening of the top and lower hinged bolts and a bolt of fastening of draft the required moment.