Peugeot 406

since 1996 release

Repair and operation of the car



Peugeot 406
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engine
+ 4. Cooling systems, heating and ventilation
+ 5. Fuel system
+ 6. System of ignition
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
- 11. Suspension bracket and steering
   11.1. Technical data
   11.2. Rotary fists
   11.3. Replacement of forward hug bearings
   11.4. The lobby is resistant
   11.5. Repair of a forward rack
   11.6. Lower lever of a forward suspension bracket
   11.7. Lower spherical hinge of a forward suspension bracket
   11.8. Stabilizer of cross stability of a forward suspension bracket
   11.9. Coulisse of the stabilizer of cross stability of a forward suspension bracket
   11:10. Lower frame of a forward suspension bracket
   11:11. Nave of a back wheel
   11:12. Replacement of bearings of a back nave
   11:13. Shock-absorber of a back suspension bracket
   11:14. Cylindrical spring of a back suspension bracket
   11:15. Pin of a nave of a back suspension bracket
   11:16. Lower lever of a back suspension bracket
   11:17. Top lever of a back suspension bracket
   11:18. The directing lever of a back suspension bracket
   11:19. Draft of a back suspension bracket
   11:20. Stabilizer of cross stability of a back suspension bracket
   11:21. Coulisse of the stabilizer of cross stability of a back suspension bracket
   11:22. Steering wheel
   11:23. Steering column
   11:24. Intermediate shaft of a steering column
   11:25. Ignition lock
   11:26. Steering mechanism
   11:27. Replacement of protective covers of the steering mechanism
   11:28. Removal of air from system of steering with the amplifier
   11:29. Pump of the amplifier of steering
   11:30. Spherical hinge of steering draft
   11:31. Steering draft
   11:32. Angles of installation of wheels
+ 12. Body
+ 13. Electric equipment
+ 14. Main malfunctions




2438a55b

11:14. Cylindrical spring of a back suspension bracket

Removal

PERFORMANCE ORDER
1. Lift a back part of the car and record on supports. Remove the corresponding back wheel.
2. Establish a jack under the external end of the back lower lever and raise the lever so that the spring was slightly compressed.
3. Unscrew an external hinged bolt of the lever (it is specified by an arrow).
4. Unscrew a nut from an internal hinged bolt of the lever.
5. Unscrew the lower bolt of fastening of the back shock-absorber.
6. Disconnect tubes of the brake system and electric wires from fastening brackets on the lower lever.
7. Slowly lower a jack before liberation of a spring. Remove a spring together with its top and lower nests.
8. Check a condition of a spring.

Installation

PERFORMANCE ORDER
1. Establish the lower and top nests of a spring on the places. Grease a rod of the shock-absorber and the place of fastening of the lower part of the shock-absorber with Molykote G Rapide Plus lubricant.
2. Establish a spring on the place and by means of a jack lift the lever, checking that the ends of a spring correctly became in nests.
3. Combine the lower lever with a nave and insert an external hinged bolt. Screw new nuts on internal and external hinged bolts, tightening them by hand.
4. Combine the lower part of the shock-absorber with the lower lever, insert a bolt of fastening and screw on it a new nut by hand.
5. Lower a jack and release the lower lever. Fix on the lower lever brake tubes and electric wires by fastening brackets.
6. Establish a back wheel and lower the car. Shake the car that elements of a suspension bracket rose on the places. Tighten nuts the required moment.