Peugeot 406

since 1996 release

Repair and operation of the car



Peugeot 406
+ 1. Maintenance instruction
+ 2. Maintenance
+ 3. Engine
+ 4. Cooling systems, heating and ventilation
+ 5. Fuel system
+ 6. System of ignition
+ 7. Coupling
+ 8. Transmissions
+ 9. Power shafts
+ 10. Brake system
+ 11. Suspension bracket and steering
+ 12. Body
- 13. Electric equipment
   13.1. Technical data
   13.2. Detection of not closed chain
   13.3. Safety locks and relay
   13.4. Switches
   13.5. Bulbs of external lighting
   13.6. Lighting lamps of salon
   13.7. Devices of external lighting
   13.8. Adjustment of light of headlights
   13.9. Combination of devices
   13:10. Multipurpose display
   13:11. Lighter
   13:12. Hours
   13:13. Sound signal
   13:14. Screen wiper lever
   13:15. Engine of a screen wiper and draft
   13:16. Back screen wiper
   13:17. Windscreen washer
   13:18. Automobile radio tape recorder
   13:19. Column (dynamics)
   13:20. Antenna
   13:21. Control system cruise control
   13:22. Anticreeping system and immobilizer of the engine
   13:23. Electric units of forward sitting
   13:24. Safety cushion
   13:25. Safety cushion elements
   + 13:26. Electric circuits
+ 14. Main malfunctions




2438a55b

13:17. Windscreen washer

Removal and installation

PERFORMANCE ORDER
Washer reservoir
1. The tank of windscreen washer is located behind the right forward wing. In a motor compartment uncover a jellied mouth and unscrew a jellied mouth from a washer reservoir (the nut of fastening of a mouth is specified by an arrow).
2. Lift a forward part of the car and record on supports. Remove the right forward wheel. Unscrew screws and remove a wheel arch insert.
3. Merge liquid from a tank for what take a rubber stopper in the tank basis. After a liquid effluence from a tank establish a stopper into place.
4. Release collars and disconnect hoses (1) from the washer pump. Disconnect the electric socket (2) from the pump of a washer and the sensor of level of liquid.
5. Unscrew a bolt (it is specified by an arrow) fastenings of the top part of a tank and remove a tank.

Prevention

Due to the limitation of space for unscrewing of a bolt of fastening of a tank, perhaps, it is necessary to remove a headlight.


6. Installation is made in the sequence, the return to removal.
Washer pump
7. Disconnect the electric socket and a hose of supply of liquid from the pump. Merge liquid from a tank.
8. Separate the pump from a tank and remove a sealing ring.
9. Installation is made in the sequence, the return to removal. Establish a new sealing ring of the pump.
The liquid level sensor in a washer reservoir
10. Lift a forward part of the car and record on supports. Remove the right forward wheel. Unscrew screws and remove a wheel arch insert.
11. Disconnect the electric socket from the liquid level sensor in a washer reservoir and take the sensor from a tank. Remove a sealing ring.
12. Installation is made in the sequence, the return to removal. Establish a new sealing ring of the sensor.
Windshield washers
13. Open a cowl and disconnect hoses from a windshield washer. Press brackets of fastening and take a washer from a cowl.
14. Installation is made in the sequence, the return to removal. Check the direction of a stream of the liquid given by a washer nozzle on a windshield.
Washer of a back door
15. Open a back door, unscrew screws and remove a spoiler from the top part of a back door.
16. Disconnect a hose of a washer and remove it from a spoiler.
17. Installation is made in the sequence, the return to removal.
Washer of headlights
18. Remove a front bumper.
19. Disconnect a hose from a washer, unscrew screws of fastening and remove a headlight washer from a bumper.
20. Installation is made in the sequence, the return to removal.